Description

• CDS products are single component

• All-Green Marine Grade coating made in Singapore

• Designed for heat reduction, waterproofing and corrosion protection

​

Environmental Requirements

• Application temperatures:

  • It is not recommended to apply if ambient weather temperature is below 13 ̊C (55 ̊F) or above 38 ̊C (100 ̊F)

  • It is not recommended to apply if surface temperature is below 13 ̊C (55 ̊F) or above 49 ̊C (120 ̊F)

• Dew point not to be lower than -15 ̊C (5 ̊F) of air temperature (Check your local dew point to determine when you should apply. The product will not dry properly and you will have to re-coat)

• Relative humidity to be below 85%

• Wind velocity should not exceed 7m/s

• DO NOT APPLY IN RAIN OR IF RAIN IS EXPECTED TO OCCUR WITHIN 4 HOURS OF PRODUCT DRY TIME

​​

Uses

• Applies on 99% of substrates to address thermal, corrosion or waterproofing concerns

​

Surface Preparation

• Substrate should be clean and dry

• Clean surface thoroughly using degreaser or detergent to remove any film, scale, loose material, oils or foreign material that will inhibit bonding

• Wire brush or wire wheel is acceptable to remove any loose rust

 

DIRECTIONS:

• Apply only to clean, dry, stable surfaces

• Apply CDS Bond first to the area desired

• Apply first coat of CDS Armour to the prepared surface by roller, brush or spray

• Apply one complete thin coat and allow to dry for 12 to 24 hrs (depending on the local dew point)

• Multiple thin coats are recommended (apply 1 coat for basic waterproof or more for complete corrosion defence as desired)

• Brush or Roll on at 11mills wet film thickness

• Spray guns and spray tips: Use a heavy duty spray unit (the product is heavy and thick, do not use thinners) and a large diameter spray tip

• Spray coatings are recommended to allow the first coat to dry tack free before applying further coatings

• Clean up with soap and water

 

WARNINGS:

• KEEP FROM FREEZING

• DO NOT THIN OR DILUTE THIS PRODUCT

• ANY CHANGE TO THE CONTENTS OF THIS CONTAINER WILL VOID WARRANTY • READ PRODUCT DATA SHEET AND MATERIAL SAFETY DATA SHEET PRIOR TO USE

​

Coverage

• CDS Armour will typical cover 40m2 to 50m2 per 20L pail depending on substrate surface and thickness of application

 

Packaging

• CDS Armour is available in 20L pail

 

Shelf Life

• 5 years in unopened pail

 

Storage

• Store in a cool dry place out of direct sunlight and heat

• Never allow the product to freeze in liquid form, once applied and cured, CDS Products can withstand any freeze thaw cycle

​

Health & Safety

• Inhalation: Remove individual to fresh air, if irritation persists, seek medical attention

• Skin contact: Flush with water

• Eye contact: Flush with water for 15 minutes while holding eyelids open

• Ingestion: Give 2 glasses of water to drink and seek medical attention

• Note to physician: Inhalation of product mist may cause headache and nausea

 

Hazards Statements

• Avoid breathing dust / fume / gas / mist / vapours / spray

• Contaminated work clothing should not be allowed out of the workplace

• Wear protective gloves / protective clothing / eye protection / face protection

​​

Precautionary Statements

• If on skin: Wash with plenty of water and soap

• If skin irritation or rash occur, get medical advice / attention

• Take off contaminated clothing and wash before reuse

​

Disclaimer

The use of this product is beyond the manufacturer’s control and liability is restricted to the replacement of material proven faulty. The manufacturer is not responsible for any loss or damage arising from incorrect usage. Specifications are subjected to changes without prior notice. Before application, customers and users are requested to check with Corrosion Defence Systems Pte Ltd and/or our authorised distributor to verify suitability of application for our products.